毛細管粘度計按結構、形狀可分為烏氏、芬氏、平氏、逆流四種。它們測定的樣品粘度是運動粘度。已廣泛地運用在石油、化工、輕工、機電、國防、交通、煤碳、冶金、醫藥、食品、造紙、紡織、科研、高等院校等單位。
測定原理:在一定溫度下,當液體在直立的毛細管中,以*濕潤管壁的狀態流動時,其運動粘度與流動時間成正比。測定時,用已知運動粘度的液體作標準,測量其從毛細管粘度計流出的時間,再測量試樣自同一粘度計流出的時間,則可計算出試樣的粘度。 正確使用毛細管粘度計,對確保產品質量和科研數據的準確是很重要的。 | |||||||||||||||||||||||||||||||||||||
三、恒溫及調垂直: | |||||||||||||||||||||||||||||||||||||
把裝好樣品的粘度計放到恒溫槽架子上(夾子上),把毛細管左、右、前、后調垂直,在測定溫度下恒溫10分鐘,開始測定,記下*到第二圈線間流出時間,一般選行三次(去掉不正常)取平均數。 | |||||||||||||||||||||||||||||||||||||
四、可用毛細管內徑、測樣品粘度范圍、可參考下表:(選用的粘度計被測樣品流出時間不低于200秒) | |||||||||||||||||||||||||||||||||||||
|
美國Cannon玻璃毛細粘度管測試方法:ASTM D445, ASTM D446, ASTM D2170方法,透明和不透明液體運動粘度測定法 (包括計算動力粘度),玻璃毛細管運動粘度計的規格及使用說明,瀝青運動粘度的試驗方法
原理:本法用以測定透明與不透明產品的粘度,它是在已知的溫度下,利用液體本身的重力流動性(gravity-flow)來測定一定體積的液體通過經校正后的毛細玻璃管粘度計所需的時間。根據所測出的動力粘度可計算出公制粘度或粘度(dynamic viscosity)。
方法概要:取一定體積的液體在嚴格的溫度與固定的液面高度的控制下,使其流經毛細管粘度計而計算其流經時間。根據流經時間與粘度計的校正常數的乘積即可得動力粘度。
所需儀器:
1. 粘度計: 校正過后的玻璃毛細管,其所測得的粘度能符合于所要求的復驗準確度再試準確度。
2. 粘度計支架: 能將粘度計在恒溫槽中架持穩固,且能使其垂直豎立。
3. 粘度計調溫槽: 內盛裝透明液體,能使樣品于粘度計內較液面低20mm以下,或高于槽底20mm以上,能保持槽內溫度的變動于15至100℃間低于±0.02℃的變化,在此溫度范圍以外,亦不超過±0.05℃的溫度變化。
4. 測溫器: 檢驗動力粘度計的溫度計內盛有適當?shù)囊后w,使之能符合溫度范圍,溫度計使用前均需校正,校正后準確度在±0.02℃,若其它測溫器有上述的度時亦可采用。
5. 定時器: 秒表或彈簧裝置的定時器均可使用,但其刻度至少在0.1秒,其測定200秒至900秒的誤差在±0.07%以內。
類型一:Cannon-Fenske、Cannon-Ubbelohde Cannon-Ubbelohde Dilution Viscometers | ||
毛細粘度管號 | 常數CSt/秒 | 范圍CST |
NO.25 | 0.002 | 0.5-2 |
NO.50 | 0.004 | 0.8-4 |
NO.75 | 0.008 | 1.6-8 |
00 | 0.015 | 3--15 |
50 | 0.035 | 7-35 |
NO.200 | 0.1 | 20-100 |
NO.300 | 0.25 | 50-250 |
NO.350 | 0.5 | 100-500 |
NO.400 | 1.2 | 240-1200 |
NO.450 | 2.5 | 500-2500 |
NO.500 | 8 | 1600-8000 |
NO.600 | 20 | 4000-20000 |
NO.650 | 45 | 9000-45000 |
NO.700 | 100 | 20000-100000 |
類型二:Ubbelohde Viscometers | ||
NO.0 | 0.001 | 0.3-1 |
NO.0C | 0.003 | 0.6-3 |
NO.0B | 0.005 | 1--5 |
0.01 | 2--10 | |
C | 0.03 | 6--30 |
B | 0.05 | 10-50 |
NO.2 | 0.1 | 20-100 |
NO.2C | 0.3 | 60-300 |
NO.2B | 0.5 | 100-500 |
NO.3 | 1 | 200-1000 |
NO.3C | 3 | 600-3000 |
NO.3B | 5 | 1000-5000 |
NO.4 | 10 | 2000-10000 |
NO.4C | 30 | 6000-30000 |
NO.4B | 50 | 10000-50000 |
NO.5 | 100 | 20000-100000 |
類型三:Zeitfuchs Cross-arm | ||
0.003 | 0.6-3 | |
NO.2 | 0.01 | 2--10 |
NO.3 | 0.03 | 6--30 |
NO.4 | 0.1 | 20-100 |
NO.5 | 0.3 | 60-300 |
NO.6 | 1 | 200-1000 |
NO.7 | 3 | 600-3000 |
NO.8 | 10 | 2000-10000 |
NO.9 | 30 | 6000-30000 |
0 | 100 | 20000-100000 |
Ubbelohde Viscometers | |||
Uncalibrated UBU | Calibrated UBC | Calibrated UBXC | |
NO.0 | 9721-N50 | 9721-R50 | 9721-U50 |
NO.0C | 9721-N53 | 9721-R53 | 9721-U53 |
NO.0B | 9721-N56 | 9721-R56 | 9721-U56 |
9721-N59 | 9721-R59 | 9721-U59 | |
C | 9721-N62 | 9721-R62 | 9721-U62 |
B | 9721-N65 | 9721-R65 | 9721-U65 |
NO.2 | 9721-N68 | 9721-R68 | 9721-U68 |
NO.2C | 9721-N71 | 9721-R71 | 9721-U71 |
NO.2B | 9721-N74 | 9721-R74 | 9721-U74 |
NO.3 | 9721-N77 | 9721-R77 | 9721-U77 |
NO.3C | 9721-N80 | 9721-R80 | 9721-U80 |
NO.3B | 9721-N83 | 9721-R83 | 9721-U83 |
NO.4 | 9721-N86 | 9721-R86 | 9721-U86 |
NO.4C | 9721-N89 | 9721-R89 | 9721-U89 |
NO.4B | 9721-N92 | 9721-R92 | 9721-U92 |
NO.5 | 9721-N95 | 9721-R95 | 9721-U95 |
Cannon-Fenske Routine | ||
Uncalibrated CFRU | Calibrated CFRC | |
NO.25 | 9721-A50 | 9721-B50 |
NO.50 | 9721-A53 | 9721-B53 |
NO.75 | 9721-A56 | 9721-B56 |
00 | 9721-A59 | 9721-B59 |
50 | 9721-A62 | 9721-B62 |
NO.200 | 9721-A65 | 9721-B65 |
NO.300 | 9721-A68 | 9721-B68 |
NO.350 | 9721-A71 | 9721-B71 |
NO.400 | 9721-A74 | 9721-B74 |
NO.450 | 9721-A77 | 9721-B77 |
NO.500 | 9721-A80 | 9721-B80 |
NO.600 | 9721-A83 | 9721-B83 |
NO.650 | 9721-A86 | 9721-B86 |
NO.700 | 9721-A89 | 9721-B89 |
Cannon-Fenske opaque | ||
Uncalibrated CFOU | Calibrated CFOC | |
NO.25 | 9721-E50 | 9721-F50 |
NO.50 | 9721-E53 | 9721-F53 |
NO.75 | 9721-E56 | 9721-F56 |
00 | 9721-E59 | 9721-F59 |
50 | 9721-E62 | 9721-F62 |
NO.200 | 9721-E65 | 9721-F65 |
NO.300 | 9721-E68 | 9721-F68 |
NO.350 | 9721-E71 | 9721-F71 |
NO.400 | 9721-E74 | 9721-F74 |
NO.450 | 9721-E77 | 9721-F77 |
NO.500 | 9721-E80 | 9721-F80 |
NO.600 | 9721-E83 | 9721-F83 |
NO.650 | 9721-E86 | 9721-F86 |
NO.700 | 9721-E89 | 9721-F89 |
Cannon-Ubbelohde Semi-Micro Viscometers | ||
Uncalibrated CUSMU | Calibrated CUSMC | |
NO.25 | 9721-G50 | 9721-H50 |
NO.50 | 9721-G53 | 9721-H53 |
NO.75 | 9721-G56 | 9721-H56 |
00 | 9721-G59 | 9721-H59 |
50 | 9721-G62 | 9721-H62 |
NO.200 | 9721-G65 | 9721-H65 |
NO.300 | 9721-G68 | 9721-H68 |
NO.350 | 9721-G71 | 9721-H71 |
NO.400 | 9721-G74 | 9721-H74 |
NO.450 | 9721-G77 | 9721-H77 |
NO.500 | 9721-G80 | 9721-H80 |
NO.600 | 9721-G83 | 9721-H83 |
NO.25 | 9721-G50 | 9721-H50 |
NO.50 | 9721-G53 | 9721-H53 |
Cannon-Ubbelohde | ||
Uncalibrated CUU | Calibrated CUC | |
NO.25 | 9721-J50 | 9721-K50 |
NO.50 | 9721-J53 | 9721-K53 |
NO.75 | 9721-J56 | 9721-K56 |
00 | 9721-J59 | 9721-K59 |
50 | 9721-J62 | 9721-K62 |
NO.200 | 9721-J65 | 9721-K65 |
NO.300 | 9721-J68 | 9721-K68 |
NO.350 | 9721-J71 | 9721-K71 |
NO.400 | 9721-J74 | 9721-K74 |
NO.450 | 9721-J77 | 9721-K77 |
NO.500 | 9721-J80 | 9721-K80 |
NO.600 | 9721-J83 | 9721-K83 |
NO.650 | 9721-J86 | 9721-K86 |
NO.700 | 9721-J89 | 9721-K89 |
Cannon-Ubbelohde Dilution Viscometers | ||
Uncalibrated CUDU | Calibrated CUDC | |
NO.25 | 9721-L50 | 9721-M50 |
NO.50 | 9721-L53 | 9721-M53 |
NO.75 | 9721-L56 | 9721-M56 |
00 | 9721-L59 | 9721-M59 |
50 | 9721-L62 | 9721-M62 |
NO.200 | 9721-L65 | 9721-M65 |
NO.300 | 9721-L68 | 9721-M68 |
NO.350 | 9721-L71 | 9721-M71 |
NO.400 | 9721-L74 | 9721-M74 |
NO.450 | 9721-L77 | 9721-M77 |
NO.500 | 9721-L80 | 9721-M80 |
NO.600 | 9721-L83 | 9721-M83 |
Zeitfuchs Cross-arm Viscometers | ||
ZCAC | ZCAXC | |
9723-S50 | 9723-U50 | |
NO.2 | 9723-S53 | 9723-U53 |
NO.3 | 9723-S56 | 9723-U56 |
NO.4 | 9723-S59 | 9723-U59 |
NO.5 | 9723-S62 | 9723-U62 |
NO.6 | 9723-S65 | 9723-U65 |
NO.7 | 9723-S68 | 9723-U68 |
NO.8 | 9723-S71 | 9723-U71 |
NO.9 | 9723-S74 | 9723-U74 |
0 | 9723-S77 | 9723-U77 |
Modified Koppers Vacuum Viscometers | |
25 | 9724-W50 |
50 | 9724-W55 |
100 | 9724-W60 |
200 | 9724-W65 |
400 | 9724-W70 |
Asphalt Institute Vacuum | |
25 | 9724-R50 |
50 | 9724-R55 |
100 | 9724-R60 |
200 | 9724-R65 |
400R | 9724-R70 |
800R | 9724-R75 |
貨號 | 玻璃毛細粘度管配件 |
9726-M50 | H100塑料粘度夾(適合Cannon-Fenske) |
9726-M70 | H101塑料粘度夾(適合Cannon-Ubbelohde) |
9726-M53 | H110 Neoprene粘度夾(適合Cannon-Fenske) |
9726-M79 | H113銅粘度夾(適合Cannon-Fenske Opaque) |
9726-M95 | H115 Neoprene粘度夾(適合Zeitfuchs) |
9726-M73 | H120 Neoprene粘度夾(適合Cannon-Ubbelohde) |
9726-M82 | H130銅粘度夾(適合Ubbelohde) |
9726-M76 | H131銅粘度夾(適合Cannon-Ubbelohde) |
9726-M98 | H132銅粘度夾(適合Zeitfuchs) |
9726-M99 | H133 BS/IP/SLSuspendedLevel |
9726-N15 | H140粘度計支架 |
9726-N30 | H141粘度計支架 |
9726-N45 | H142 Cannon-Ubbelohde FilterStick |
攜品牌產品,遵循高標準服務,致力成為行業高品質服務商。
瀚默科技-專注為您
更多產品請咨詢我司銷售人員
:
上一篇:進口蠕動泵軟管分類及特性